: April 25, 2022 Posted by: bondstriet Comments: 0

How do you load a Porter Cable nail gun?

Quote from video on Youtube:Making sure the tips are pointing to the front of the magazine. And the nails are under the nail guide in the channel. Next i'll push the magazine closed until it latches into place.

How do you load a 16 gauge Porter Cable?

Quote from video on Youtube:All you do is slide the nails into the bottom up to where the other nails are. And then push down the red button. Slide that back BAM it's loaded it's that simple.

How do you load a Porter Cable air staple gun?

Quote from video on Youtube:As far as putting staples in it it's pretty straightforward. You have a release right here. And then your staples going right from the bottom. This is a smaller gauge staple by the way 22 gauge.

See also  Who do I call to report a nail salon?

How do you load a framing nailer?

Quote from video on Youtube:Pull the follower. Back. Place your fasteners in the tools magazine. And gently allow the follower to get behind the nails and push it up to the front.

How do you load a nail gun?

Quote from video on Youtube:Just by simply dropping the nails into place and then just releasing the last mechanism that slides down and holds the nails in the rack.

How do you load a pin nailer?

Quote from video on Youtube:Make sure the arrow is facing down slide the nails into the magazine. And all the way forward. Slide the magazine closed until it locks and now you can fire your 23 gauge pin nails.

Can you use 18 gauge nails in a 16 gauge nailer?

So, can you use 18 gauge nails in a 16 gauge nailer to attach exterior trim, molding, and other smaller jobs? Well, the short answer is- and we hate to tell you this-, you can’t.

Why does my Porter Cable nail gun keep jamming?

What Caused the Jam: Lack of Adequate Oil: The air cylinder in the nose needs plenty of oil to function properly. Too little oil, and the nails will be slow to feed, causing a jam. Pro Tip: For coil nailers, use 10-15 drops of oil before nailing.

How do you clear a jammed Porter Cable nail gun?

Quote from video on Youtube:Going to pull the nails out so that they're not pushing up against the hammer here as i'm working on it i wiggled the hammer.

See also  How long does White Out take to dry?

How do you reload a stapler?

Quote from video on Youtube:Once open the top by pulling gently insert the staples carefully note that the pins are facing. Down. Gently close the top.

How do you use a Porter Cable air compressor?

How To Use Porter Cable Air Compressor:

  1. Assemble the things you need first. …
  2. Find out where the air compressor’s knob is. …
  3. Fix the air hose to the compressor. …
  4. Make sure the compressor’s switch is in the ‘off’ position. …
  5. Ensure that your compressor is connected to the right power source.

How do you load a Stanley staple gun?

Quote from video on Youtube:It's got a great little feature here as well there's a locking catch on the handle. So to engage the staple ready to go simply depress the lever under the catch.

Which is bigger 18g or 16g nails?

The gauge simply communicates the fastener thickness as a whole number, but it gets confusing when looking at the actual ratings. That is because 16 is greater than 18.

What’s the difference between 16 and 18 gauge nails?

The difference between them is the gauge nail that they shoot. The most common and readily available types are 15 gauge, 16 gauge, 18 gauge, and 23 gauge. The higher the number, the thinner the nail and the smaller the hole.

Whats bigger 16 or 18 gauge nails?

Gauge is actually the number of nails that are lined up. This indicates that 16-gauge nails are thicker and can hold better when compared to 18-gauge brads. You will have to keep in mind that a low gauge number will have a thicker nail.

See also  Is it OK to frame with screws?

Why is my Porter Cable Finish Nailer not shooting nails?

Check the nail clip to be sure it is loaded and not stuck. Release the clip by depressing the lever on the bottom of the gun just in front of the air fitting. The clip should spring open, slide the clip down and check to see that there are nails present.

What causes a nail gun to not fire?

Clear Jams



Jams are the most common cause of a nailer not firing. Thankfully, they are often easy to clear. For safety, first disconnect the tool from the air supply, retract the feeder mechanism, and remove any excess fasteners from the magazine. From there, clearing the jam depends on what type of nailer you have.

What type of nails does a Porter Cable nail gun use?

Product Description



The PORTER-CABLE PFN16200-1 2-Inch, 16 Gauge Finish Nails are galvanized coated with chisel point tips.

What do 15 gauge nails look like?

Quote from video on Youtube:Here we can see that the 15 gauge has got a rounded D shape. Head while the 16 gauge has a T shape. And we can see comparison a thickness between the two.

What size finish trim nails?

Finish (Trim) Nailer: Primarily for shooting 16-gauge or 15-gauge nails. They use a finish nailhead, easily identified by being stored at an angle on the nailer. This angle also allows for easy access in tight spots.